Therefore, tubes, fittings, and valves with a smooth internal surface like SF1 (Mechanical polished) or SF4 (Electro-polished) are extensively installed with the advantages of cleaning easily and avoiding bacteria contamination.

CSE only offers ASME certified tubes that are manufactured, quality controlled, marked, and certified complying with the highest standards for hygienic equipment design and guarantees extended quality and traceability.

CSE BPE tubing's reduces inspection requirements prior to installation by utilizing only the quality stainless steel materials compliant with ASME regulations.

CSE delivers directly from stock the following stainless steel tubes in grade TP316L with low sulfur content of 0.005% to 0.0017% and SF1 and SF4 finishes (according to the ASME BPE specification).

Specification:

• ASTM A270-2015 S2
• SURFACE FINISH: SF0~SF6
  
  • SF1 ID Pol. Ra<0.5μm/ OD Pol. Ra<0.8μm
  • SF4 ID EP Finished Ra<0.38μm/ OD Pol. Ra<0.8μm
• CSE BPE EP products with following advantages:
  
  • Homogeneously EP layer to minimize rouging
  • Higher chrome concentration for better corrosion resistance
  • Guaranteed smoothness of all internal surfaces to reduce Bio film

CSE GROUP offers various shapes, end connections, configurations, dimensions and inner surface finish options SF1~SF6 that comply with ASME BPE standards. To prevent damage and contamination, all BPE hygienic fittings are inspected and packaged in CLASS 10,000 clean room to get capped and transported in transparent bags. After strict inspection by CSE, each BPE fitting will be laser on the pipe fittings according to ASME BPE-2019 symbol requirement, and a material test report (MTR) will be provided.

Specification:

• ASTM A270-2015 S2
• SURFACE FINISH: SF0~SF6
  
  • SF1 ID Pol. Ra<0.5μm/ OD Pol. Ra<0.8μm
  • SF4 ID EP Finished Ra<0.38μm/ OD Pol. Ra<0.8μm
• CSE BPE EP products with following advantages:
  
  • Homogeneously EP layer to minimize rouging
  • Higher chrome concentration for better corrosion
    resistance
  • Guaranteed smoothness of all internal surfaces to reduce Bio film
• Dimension：
  • 1/2" ~6"
• Material：low sulphur
  • ASTM SS316L, S：≦ 0.005% ~ 0.017%,

• The sanitary diaphragm valve use Purity block or Forged material such as SS316L and precision machining body. Seal can be provide EPDM/ PTFE as FDA USP IV qualify gasket.
• The end connection can be provide welded, clamp, weld/ clamp/ weld etc...
• Manual or Pneumatic control can be option( can be select the control box)
• The inner surface treatment can reach
  • 15RAμin (0.38μm) as SF4 (Electro-polished)
  • 20RAμin (0.51μm) as SF1 (Mechanical polished)
  • The grade of 3A 32RAμin (0.81μm)

For improvement of the medicines purity, hygienic process, CSE has designed a T/U-type aseptic diaphragm valve with zero dead ends, which reduces the scope of bacterial growth. It can be widely used in food, beverage, dairy, brewing, pharmaceutical and other industries. PW (Pure water)& WFI (water of injectioin) , ultra-high purity chemicals, etc.

No only CSE standard diaphragm valves, we can also provide aseptic sampling diaphragm valves and Multi-port block diaphragm valves  for reduce Space and more less dead angle design by according to customer requirements.

Specification:

• Size :
  • 1/2",3/4",1",1.5",2"
• Operation :
  • Normal Open & Normal Close design
• Connection type:
  • Clamp or Weld or other …
• Connection:
  • INCH: 1/2”~2”
  • DIN / ISO: DN10-DN50
  • other size can be requirement 
• Working temp：
  • ASSEMBLING Diaphragm：
    • EPDM(-40 C ~150 C0
    • PTFE/EPDM(-10 C~150 C)
• Working pressure：
  • max 10 Bar
• Surface :
  • Standard :OD /ID mirror polished. ID Ra 0.8um
  • OD- Sand Blasted .or E/P or other ,ID Ra 0.38um

CSE GROUP Diaphragm valves

According & Approval by PIC/S GMP standard  also qualify by National Institutes of Health (NHRI)...and other famous pharmaceutical companies.

The design of this diaphragm valve can be widely used in systems with high aseptic requirements such as food, beverage, dairy products, brewing, biopharmaceutical fields and water for injection.

Specification

• Material:
  
  • Body:Forged/316L
  • Diaphragm:EPDM+PTFE/NC or NO
    The seal of Diaphragm is exchangeable
    with GEMU
• Connection:
  
  • Clamp end/weld end
• Body type:
  
  • Direct connection(two way)/equal T/
    reducing T/U-point.....
• Operation:
  
  • Normal open/normal close
• Work temp:
  
  • Diaphragm:EPDM+PTFE(-10°C~150°C)
• Work pressure:
  
  • Max:10 Bar
• Surface:
  
  • SF1:ID polished to Ra≦0.5μm
  • SF4:EP finished to Ra≦0.38μm
  • ID/OD mirror polished & ID Ra≦0.5μm/OD sand blasted.....

No residue design

The product adopts a 45-degree downward discharge design so that there is no residue in the body, and can be designed with CIP or high-temperature cleaning, which truly meets the pharmaceutical-grade standard.

Sync in Europe and America

CSE tank bottom valve is not only easily assemble and disassemble, but also sold to Europe, America and all over the world, and is widely used in food, medicine and biochemical factories.

Specification:

• Size :
  • 1/2",3/4",1",1.5",2"
• Operation :
  • Normal Open & Normal Close design
• Connection type:
  • Clamp
  • Weld
  • other …
• Standard:
  • INCH: 1/2”~2”
  • DIN / ISO: DN10-DN50
  • other size can be requirement
• Working temp：
  • ASSEMBLING Diaphragm：EPDM(-40 C ~150 C0、PTFE/EPDM(-10 C~150 C)
• Working pressure：
  • max 10 Bar (1000kpa)

CSE use purity Block or Bar material with High technical Precision Machining process for aseptic inner flow design.

• Surface Finished:
  • Surface can be meet SF1 Ra
• Assembly:
  • The multi-port direction valve body is convenient to connect to different tubing-lines which can save installation time and space, it can also be designed according to customized requirements as multi-angle or installing location.
• Function:
  • Mostly used for sampling or production and steam applications. It can simplify the traditional valve combination configuration, and the design that can reduce the dead angle and ensure complete drainage to achieve the effect of sterilization.

Specifications

• Material:
  • Body: Forged/316L
  • Diaphragm: EPDM+PTFE/NC or NO
• Connection
  • Clamp End/Weld End…
• Body Type
  • Direct Connection (Two Way)/Equal T / Reducing T/U-Point…
• Operation
  • Normal Open / Normal Close
• Work Temp
  • Diaphragm: EPDM+PTFE (-10ºC~150ºC)
• Work Pressure
  • Max: 10 Bar
• Surface
  • SF1: ID Polished to Ra≤0.5μm / SF4: EP Finished to Ra􀀀0.38μm
    ID/OD Mirror Polished & ID Ra≤0.5μm / OD Sand Blasted…

The design of the ball gasket has passed FDA certification and qualified material.

Gasket Material can options for PTFE、PTFE+Carbon、PTFE+GB、PTFE+50%SS. as your function needs.

CSE ball valves are suitable for sticky liquids or liquids containing granules, such as the food industry, biotechnology, beverage, chemical and pharmaceutical industries.

Specification:

• Size:
  • 1/4”- 6”
  • DN50~ DN80
• Material: 
  • 316/ 316L/ CF3...etc.
• Ball seat material:
  • PTFE
  • PTFE+Carbon
  • PTFE+GB
  • PTFE+50%SS
• Max Temperature:
  • -10°C~ 130°C
• Standard End:
  • SMS
  • RJT
  • DIN
  • 3A
  • ISO
  • Weld end
  • Clamp end
  • Male/ Male
  • other can be required

It is widely used in semiconductors, biopharmaceutical industry, food, dairy products, breweries and beverages, and so on. It is convenient for customers to analyze samples collected from piping systems or storage tanks. It can also be assembled at the bottom of the tank or at the end of the pipe for slag discharge. The shape and interior of the injection valve are treated with CSE specially designed for high-purity fluid equipment, with zero dead angles to avoid the risk of bacterial accumulation.

The surface finish of the valve, our valves are polished to meet ASME BPE standards.

Specification

• Surface finish of the valve
  • Machined surface
  • Mechanical polishing
  • Mirror polishing
  • Electrolytic polishing... RA
• Material:
  • SS316L
• Size:
  • 1/2”-2”.
• Connection ends:
  • Clamp/ Weld/ or Male, Female end.

• Materials:
  • Stainless steel SS316L
• Seal rings:
  • Body - EPDM Rubber or Silicone/Viton (FKM) /PTFE.
  • Plunger- EPDM Rubber or Silicone/Viton (FKM) /PTFE.
• Surface Finish:
  • OD≦0.8 , ID≦0.8 or 0.4μm
  • Electric polish ....etc.
• Connections:
  • Weld
  • Clamp
  • SMS
  • DIN
  • RJT
  • 3A
  • Male/ Female end
• Type:
  • Middle Clamp design
  • Or Flange high pressure design.
• Special requirement:
  • Middle with leg plunger for safety horizontal Link can be a requirement.
• Max Work pressure :
  • 10 Bars.

The CSE metal Bellow thermal steam trap is automatically closed when the pipeline steam temperature circuit reaches saturation, preventing steam frozen into water through the steam trap. Easy to obtain Pure steam has been widely used in the pharmaceutical manufacturing process, and keeps max pure steam in the pipeline to save heat waste.

All parts are made of stainless steel, complete design can be horizontal & vertical inlet and outlet assembly, precision operation suitable for pure steam SIP/ CIP process is widely used in biopharmaceutical, aseptic, food and beverage applications.

• Connection end:
  • Clamp ends/ Weld ends...etc.
• Surface finished:
  • Polished
  • Electro polished
• Size:
  • 1/2”-2”
• Middle connection:
  • Clamp design for easy clean and repair.

B type- Thermodynamic Steam Traps

B "The CSE metal thermal steam trap is automatically closed when the pipeline steam temperature circuit reaches saturation, Preventing steam from freezing into water through the steam trap . Pure steam has been used in the pharmaceutical manufacturing process, and keeps max pure steam in the pipeline to save heat waste.

All parts are made of stainless steel, complete design, easy horizontal inlet and outlet assembly, low cost and easy to maintain, suitable for pure steam SIP /CIP process width use for biopharmaceutical and aseptic food and beverage applications. The thermal steam trap discharges condensate close to the saturation temperature.

• CSE can be offer kinds of the steam traps, the common characteristics of steam traps as following points:
  • Drain the condensate from the pipe
  • Collect steam
  • Exhaust air and gas

• Connect:
  • Clamp /Weld ...etc.
• Surface:
  • Polish. Or Electric polish.
• Size:
  • 1/2”-2”.
• Traps are widely used in industries where condensate must be quickly removed.

The stainless steel sanitary filter reduces the entry of impurities in the process to help you ensure the highest purity. It can be widely used in beverages, cosmetics, dairy products, food and pharmaceutical industries. The filter screen is available for customers to choose from metal plain weave mesh, stacked weave mesh and wedge mesh. It can also be adjusted according to customer requirements for filter media, such as a screen for filtering large particles. If it is to remove finer particles, it It can be equipped with a spare pipe and a screen with small holes, which not only improves product quality and hygiene, but also helps protect processing equipment. It is very suitable for equipment including homogenizers, meters, nozzles, needle valves and pumps. The free-flowing design and stainless steel structure provide the best hygiene and corrosion resistance.

Product specifications:

• Filter style selection:
  • In-line
  • Side outlet strainer
  • Y type 
  • S  type and other styles.
• Inlet/Outlet size:
  • 1",1.5",2",2.5",3"
• Screen diameter:
  • Stainless steel filter #10(目) ~ #400(目) MESH
  • Can be adjusted according to customer needs, a variety of styles can be selected
• Port type:
  • Welded
  • Tri- Clamp
  • Thread Ends
  • Flange type.

The sterilization chamber uses high temperature steam to completely sterilize the spindle to avoid any pollution into the Valve Inner chamber.

Aseptic control valves are widely used in applications in the food and pharmaceutical industries, biotechnology and ultra-clean applications. CSE provides convenient maintenance, disassembly and installation design. The valve body adopts 316L anti-corrosion material and aseptic special PTFE seat. The surface finish also reaches the 0.6 Ra standard for aseptic applications. If you need a higher quality surface finish than 0.6 Ra, you can apply to CSE.

CSE can also provide various directional valves for different applications.

Specification

• Material:
  • Valve body: SS316L
  • Sterilize Block: SS304
• Valve Size:
  • 1/2"-4"
• Valve Connection
  • clamp ends
  • welding ends
  • male and female ends
• Steam Nozzle
  • NPT 5/16 thread

The design of the aseptic threaded joint can ensure that the O-ring part is inserted into the O-ring fixed collar connection to avoid squeezing, ensuring that the components are connected in a smooth, gap-free and O-ring connection to reduce residue retention And effectively improve production efficiency and reduce cleaning time. CSE uses durable, corrosion-resistant stainless steel 316L to produce DIN aseptic series components, which are widely used in aseptic applications such as biopharmaceuticals.

O-ring joints and groove seals are identical in the two standards.

DIN 11864-1, Threaded connections with long ends

DIN 11864-2, Flange connections with long ends

DIN 11864-3, Clamp connections with long ends

DIN 11853-1, Threaded connections with short ends

DIN 11853-2, Flange connections with short ends

DIN 11853-3, Clamp connections with short ends

To meet the strict demands of the biotechnology, cosmetics, chemical, pharmaceutical, and food and beverage industries.

Specification

• Materials:
  • ASTM 304
• Size Range:
  • 1/2" ~ 8"

• Materials: ASTM 304
• Size Range: 1"~6"

This USP VI standard is not only applied to the pharmaceutical and biotechnology industries but also multi-functional for use in sanitary and different industries.

CSE can provide a variety of PTFE, EPDM/PTFE. seals, sanitary ball valve ball Seat, gaskets and seals for apply use in width range CSE purity, hygienic & pharmaceutical products.

CSE tube fittings can be used for sanitary, pharmaceutical, vacuum...etc. purposes.

• Specification: 
  • 3A
  • ISO 2852
  • IDF
  • DIN 11850
  • BS1528...etc.

• Size: 
  • 1/2 "-12"
  • DN10-DN200
• Material: 
  • SS304
  • 316L
  • TP316L

• Martial:
  • SS 304
  • 316L ....
• Size:
  • 1/2” to 12” for selection.
• Connection:
  • Clamp
  • weld end
  • Male/Female ...
• Surface:
  • Satin polish
  • Mirror
  • Vibrate
  • pickled
  • Sand blast
  • E/P...
• Products Range:
  • Elbow：Long/Short 90°/45 ° Elbow R=1.5D.
  • TEE： Equal Tee, Pull Tee, reducer Tee, Cross, U Tee…
  • Reducer: Concentric, Eccentric ...
• OEM:
  • any special OEM services ...

• Material:
  • SS304
  • 316L
• Size:
  • DN10-DN104 for selection.
• Surface:
  • Satin polish
  • Mirror Polish
  • Vibrate
  • pickled
  • Sand blast
  • E/P...
• Connection:
  • Weld end
  • Male end
  • Female end...
• Products Range:
  • Elbow：Long /Short 90 °/45 °Elbow. R=1D. Short R=1.5D
  • TEE：Equal Tee, Pull Tee, reducer Tee, Cross, U Tee…
  • Reducer: Concentric, Eccentric ...
• OEM :
  • any Y Tee, and special OEM services ...

• Material:
  • DIN 1.4401
  • DIN 1. 4404
  • SS304
  • 316L
• Size:
  • DN10-DN200 for selection.
• Surface:
  • Satin polish
  • Mirror polish
  • Vibrate
  • pickled
  • Sand blast
  • Electroc Polish
• Connection:
  • Weld end
  • Male end
  • Female end...
• Products Range:
  • Elbow ：Long Elbow/ Short Elbow/ 90 °Elbow/ 45 °Elbow.
  • TEE：Equal Tee, Pull Tee, Reducer Tee, Cross, U Tee…
  • Reducer: Concentric, Eccentric ...
• OEM: 
  • Any Y Tee
  • special OEM services ...
    

• Martial:
  • SS304
  • 316L
• Size:
  • 1/2” -12” for selection
• Surface:
  • Satin polish
  • Mirror
  • Vibrate
  • pickled
  • Sand blast
  • E/P...
• Connection:
  • Weld end
  • Male end
  • Female end
• Products Range:
  • Elbow ： Long /Short 90°/45° Elbow. R=1.5D
  • TEE：Equal Tee, Pull Tee, reducer Tee, Cross, U Tee
  • Reducer: Concentric, Eccentric
• OEM:
  • any Y/ and special OEM services ...

Specification

• Product specifications:
  • The product has a combination of L type/Y type/T type/F type/TT type/TL type/LT and changeable Body design type..
• Connection:
  • Butt welding type
  • Tri-clamp type
  • Male End
  • Female end
  • And accept customer's special size, connect port design.
• Size:
  • 1/2"-6".
• Material:
  • SS 316L
  • forged body
• Gasket material:
  • EPDM
  • VITON
  • PTFE with prevent fall Seal Design.
• Product advantage:
  • Pneumatic cylinder – safety & Quick replacement design during disassembly and assembly.
  • ASI control and Smart LED control Top link:
  • Joint CSE C2 Control Top with proximity switch or micro switch for allowing you to easily install and long-distance control or Manifold Valve design for combination.

• Material:
  • 304/ 316L
• Type:
  • Sanitary Tank level valve
  • Sanitary Tank Upper valve
  • Test valve
  • Diaphragm sampling valve
  • Hygienic Sample valve
• Connection:
  • PF Thread End
  • Welding Flanged end
  • Welding Ferrule End

The sanitary ball valve is made of stainless steel SS316/SS316L. In addition, it also provides surface treatment (electrolytic polishing: helps to improve corrosion resistance; mechanical polishing) that meets ASME BPE standards to ensure the cleanliness of the product line.

Specification

• Standard:
  • SMS
  • DIN
  • 3A
  • ISO
  • RJT
  • other can be selected.
• Size:
  • 1/2" to 6".
• Flow port selection:
  • 2way
  • 3way
  • 4 ways... etc.
• Ball Seat:
  • Half-cavity
  • full-cavity.
  • The ball Seat as FDA-approved materials.
• Ball Seat Material:
  • PTFE
  • PTFE+ Carbon
  • PTFE+GB
  • PTFE+50%SS...
• Auto accessories connection:
  • It can be matched with pneumatic head (single-acting Air/Spring or double-acting Air/Air) and positioner to facilitate various automatic control.
    

Specification

• Control Way:
  • manual and pneumatic control can be selected
  • pneumatic cylinder can joint with CSE C2 control box to facilitate automatic production needs.
• Size:
  • 1/2" to 4".
• Material:
  • SS316L

Specifications

• C1 Actuator
  • High bracket pneumatic head
  • It is a high bracket design, which can be installed with 2-4 screw-type proximity switch; this product has a single-acting(Air/Spring) design and a double-acting (Air/Air)design, quality guarantee 600,000 circle operations within 1 year.
  • C2 type low bracket pneumatic head
  • The low bracket design can allow the Valve disk direct link with Actuator.
  • Top spindle for Link C2 Control Top. (optional solenoid valve, micro switch or proximity )
  • single-acting(Air/Spring) design
  • double-acting (Air/Air)design
  • quality guarantee 600,000 circle operations within 1 year.
• C3 Actuator
  • low bracket Actuator
  • The C3 special low bracket design can allow the Valve disk direct link with Actuator.
  • C3 Bracket allowing 2 sets of screw-type proximity switches for signal transfer .
  • single-acting(Air/Spring) design
  • double-acting (Air/Air)design
  • quality guarantee 600,000 circle operations within 1 year.
• C101 Actuator
  • high bracket pneumatic head
  • This product is designed to enlarge the cylinder for 4"~6" high torque butterfly valves.
  • Top spindle for Link C2 Control Top. (optional solenoid valve, micro switch or proximity opening)
  • single-acting(Air/Spring) design
  • double-acting (Air/Air)design
  • quality guarantee 600,000 circle operations within 1 year.

Product Features:

• Use butterfly valve range
  • C1: 1" ~ 3" butterfly valve
  • C2: 1" ~ 3" butterfly valve
  • C3: 1" ~ 3" butterfly valve
  • C101: 4" ~ 6" butterfly.
  • CSE Actuator Special design by Gear-driven and POM piston with stainless Spring. pneumatic head for precision function.
  • For reduce Noise and vibration. And make the Valve smooth operation .special for joint the paddle of manifold valve design.
• Input Air pressure:
  • 4-6kgs/Cm2( Bars)
• Circle time
  • C1/C2/C3: 1.5 seconds
  • C101: 1.7 seconds
    

Product specifications:

• Dimensions:
  • 1/2”-6”
  • DN10-DN200
• Material
  • Body
    • 304
    • 316L (forged design)
• Rubber Seat
  • EPDM
  • SILICON
  • VITON
• Handle
  • stainless steel
  • Nylon + 13% GF
• End connetction:
  • Butt welding
  • Clamp
  • Male
  • Female
• Standard:
  • 3A
  • DIN
  • SMS
  • RJT
  • IDF
• Various handles
  • 2 position
  • 4 position of SS304 Pull Handle
  • 12 position Gripper Handle
    • Color
      • Black
      • Blue
      • Red
  • Handle color with strong Nylon 6+13% GF material
  • SS304 Gripper Handle
  • also can be choice lock device Handle for safety function.
• Material & surface finished:
  • Forged body, Disk Material which is more temperature resistant than casting and prevents rust.
  • surface roughness by CSE precision CNC Machining surface all control below Ra

Product specifications

• Dimensions:
  • 1/2"-8"
  • DN10-DN200
• Material
  • Body: 304, 316L (forged design)
  • Washer: EPDM, VITON
  • Handle: stainless steel, plastic steel
• End Connection:
  • Welded end
  • Threaded end
  • Flanged end
• Surface Finish
  • The surface roughness of the butterfly valve of our company after CNC turning is below Ra
• Forging quality
  • All butterfly valve bodies and discs are forged, which is more temperature resistant than casting and prevents rust.
    

Product specifications:

• Dimensions:
  • Suitable for 1"-3" and 4-8" CSE butterfly valves
• Material:
  • Stainless steel 304
  • Nylon material
• Multi-section handle
  • 2 position
  • 4 position pull handle
  • 12position Gripper notch handle and adjust angle handle devices.
    

Product specifications

• Dimensions:
  • 1/2”-6”
• Material:
  • Body: 304, 316L
  • Washer: EPDM, SILICON, VITON
• End Connection:
  • BS butt welding type, RJT/IDF thread mouth type.
• Forging quality:
  • All butterfly valve bodies and discs are made of forging, which is more resistant to temperature and rust than casting.
• Surface Finished:
  • The surface roughness of the butterfly valve of our company after CNC turning is below Ra

Product specifications:

• Dimensions:
  • DN10-DN200
• Material
  • Body: 304, 316L
  • Pad: EPDM, SILICON, VIOTN
• Port type:
  • DIN welding end
  • Male end
  • Female end

Product specifications

• Dimensions:
  • DN10-DN200
• Material
  • Body: 304, 316L
  • Gasket: EPDM, SILICON, VIOTN
• End connection
  • SMS welding end
  • Male end
  • Female end.
• Torque value
  • 1" <1m/kg
  • 1.5" <1m/kg
  • 2" 1.3m/kg
  • 2.5" 1.5m/kg
  • 3" 2.0m/kg
  • 4" 3.1m/kg

Product specifications:

• Dimensions:
  • DN10-DN200
• Material:
  • Body: 304, 316L
  • Gasket: EPDM, SILICON, VIOTN
• End Connection:
  • SMS welding End
  • Male End
  • Female end
• Torque value
  • 1" <1m/kg
  • 1.5" <1m/kg
  • 2" 1.3m/kg
  • 2.5" 1.5m/kg
  • 3" 2.0m/kg
  • 4" 3.1m/kg

Product specifications:

• Size:
  • 1 ~ 4" Mix-proof butterfly valve
• Material quality:
  • 304
  • 316L
• Temperature:
  • 0~130°c (varies according to oil seal material)
• Maximum pressure:
  • 10kg/2
• Export type:
  • Clip-on
  • Welding
  • Oil-free
• Control type:
  • manual handle
  • steam operated
  • can be matched with control box
• Washer material:
  • EPDM
  • SILICON
  • VITON
• Product specification:
  • 3A
  • DIN
  • SMS
  • IDF
  • RJT...
• Product Features:
  • Effectively separate different media in CIP or storage tank system
  • Leak indication can be given to the leaking seal
  • Design leak chamber for flushing connection
  • Forced mechanical drive between the leakage valve and the valve plate
    

Specification:

• Standard
  • 3A
  • SMS
  • DIN
  • BS
  • IDF...
• Size :
  • 1/2",3/4",1",1.5",2",2.5",3",4"
• Material
  • Body: 316L
  • Washer: EPDM, SILICON, VITON,PTFE.
• End Connection:
  • Welding end
  • Clamp end
  • Thread end

Specification

• Application
  • Dairy products
  • Food
  • Beverages
  • Breweries
  • Pharmaceutical Industry.
• Temperature range:
  • -5-140 C
• Maximum product pressure:
  • vacuum -10 bar
• Material:
  • Body 1.4404 (316L)
• Surface finished:
  • inside/outside: Ra 0.8um
• Seal material:
  • EPDM
  • PTFE
• Sight glass material:
  • Borosilicate
• Size
  • EN 10357-A: DN25, 40, 50, 60, 80, 100, 125, 150
  • ISO2037: ISO25, 38, 51, 63.5, 76.1, 101.6
  • ASME BPE: 1/2”-4”

Specifications:

• Dimensions
  • 1/2",3/4" 1"
  • 1.5",2",2.5",3"
• Stainless steel material
  • Body: stainless steel 316
  • Axle core: 316 or core rubber
• End Connection:
  • Welded
  • clip-on
• Standard:
  • 3A
  • RJT
  • BS
  • DIN
  • SMS threaded
  • Can be divided into 2-way and 3-way
• Surface Finished:
  • Ra 0.8um/ 0.12um etc...

Specifications:

• Dimensions:
  • 1/2",3/4" 1",1.5",2",2.5",3"
• Stainless steel material
  • Body 316
• End Connection:
  • Welded
  • clip-on
• Standard:
  • 3A
  • RJT
  • BS
  • DIN
  • SMS threaded
• Surface Finished:
  • Ra 0.8um
  • Ra 1.2um

Specifications:

• Dimensions:
  • 1/2",3/4" 1",1.5",2",2.5",3"
• Stainless steel material:
  • Body 316
• End Connection:
  • T,F, T/T, T/F...welded
  • clip-on
• Standard:
  • 3A
  • RJT
  • BS
  • DIN
  • SMS threaded
• Roughness:
  • Machincal Polish
  • Polish
  • Electric polish for Ra< 0.8um. or better..
  • can be request
• Seal:
  • EPDM
  • NBR
  • PTFE

Specifications:

• Sanitary Type:
  • The filter has in-line strainer, side outlet strainer, Y type, S typeand other styles.
• Size:
  • Inlet/Outlet size: 1/2” -12”. or special requirement ...
  • Mesh: Stainless steel #10 ~ #400 MESH
  • Connect Port type: Weld, Clamp, Flange or any Male/ Female ...

Qualify by: IP64 waterproof and dustproof,ATEX sparking explosion-proof certification and the integrated design ASI connection.

Specifications:

• C2 without LED-
  • Use for CSE up side down pneumatic cylinders such as Divert valves, pneumatic diaphragm valves, Pneumatic bottom valves, etc...
• Composition-
  • Control box body x1, dust cover X1, solenoid valve X1 (DC24V 3W or other...)
  • Micro Switch Type-Micro Switch X2 (3A 125VAC 30VDC)
  • Proximity switch type-provides the following four signals
  • PNP-NO. PNP-NC. NPN-NO. NPN-NC
• C2 LED-
  • Use for CSE up side down pneumatic cylinders such as Divert valves, pneumatic diaphragm valves, Pneumatic bottom valves, etc...
• Composition-
  • Control box body x1, LED transparent lampshade x1, LED PLC control board x1, a set of red and green LED lights, dust cover X1, solenoid valve X1 (DC24V 3W or other...)
  • Micro Switch Type-Micro Switch X2 (3A 125VAC 30VDC)
  • Proximity switch type-provides the following four signals
  • PNP-NO. PNP-NC. NPN-NO. NPN-NC
• C3 LED (patent design number M554140)-
  • Use for CSE rotating cylinders such as butterfly valves and ball valves.
• Composition-
  • Control box body x1, LED transparent lampshade x1, LED PLC control board x1, a set of red and green LED lights, dust cover X1, connecting rod 1, solenoid valve X1 (DC24V 3W or other...)
  • Micro Switch Type-Micro Switch X2 (3A 125VAC 30VDC)
  • Proximity switch type-provides the following four signals
  • PNP-NO. PNP-NC. NPN-NO. NPN-NC

CSE offers a wide variety of clamp fittings in 304 and 316L material in sizes from 1/2" to 12".
The materials are offered for food, dairy, beverage, meat processing, vacuum processing, pharmaceutical, chemical, and many other industries. Our products have earned the 3A symbol, which requires an annual assessment to make certain each product conforms in all respects to the published standard.
It is necessary you specify at the time when orders be placing if heat numbers and MTR's are required. Sanitary 3A Ferrules that CSE offers are made by forged. Service Short Weld Ferrules-14WMP, Middle Weld Ferrules-14MMP Long weld ferrules-14AMP (L14AM7), Roll-On Expanding Ferrules-14RMP, Tank Weld Ferrules (light duty)-14WLMP, Tank Weld Ferrules (heavy duty)-14MPW, Tygon Hose Adapters-14MPHT, Rubber Hose Adapters-14MPHR.
All of our 3A Ferrules could be conformed with 3A-16AMP Blank End Cap which is made by solid bar, 3A- Clamp and Seal 13PG, 13FG as well as other Adapters.

The sanitary ferrule design is easy to assemble and disassemble on the production line and is used to connect the clamp joint to the butt welded joint. Provide 304, 316 or 316L material；made of 316 stainless steel, high corrosion resistance, highly polished inside, smooth surface, can reduce the risk of bacterial growth and residue accumulation. The sanitary ferrules meet the 3-A sanitary standard, and ensure that its customers will produce safety Food, there is almost no risk of contamination. Especially for equipment manufacturers, this equates to satisfied customers who trust products approved by the USD and FDA. It can be widely used in the food industry, wine making, beverage, biopharmaceutical and other industries. 

Specification:

• Material grade:
  • 304, 316L
• Size range:
  • 1/2", 3/4", 1", 1.5", 2", 2.5", 3", 4", 6", 8", 10" and 12"

• Seal 13PG, 13FG :
  • 13PG: 1/2", 3/4", 1", 1.5", 2", 2.5", 3", 4", 6" and 8".
  • 13FG: 1/2", 3/4", 1", 1.5", 2", 2.5", 3", 4", 6", 8", 10" and 12".(10" and 12" only in Black EPDM and Silicon)
  • EPDM(Black. White is required), Silicon(Clean), Viton (Black. Green is required), PTFE(White)

DIN

The materials are offered for food, dairy, beverage, meat processing, vacuum processing, pharmaceutical, chemical, and many other industries. It is necessary you specify at the time when orders be placing if heat numbers and MTR's are required. Sanitary DIN/ SMS Ferrules that CSE offers are made by forged.
The DIN/ SMS Ferrules could be conformed with DIN/ SMS Blank End Cap which is made by solid bar, Clamp and other Adapters.

Specification:

• Material grade:
  • 304 and 316L / 1.4301, 1.4404
• Size Range:
  • DN10, DN15, DN20, DN28, DN34, DN40, DN52, DN70, DN80, DN100, DN125, DN150, DN200

• Standard:
  • DIN 11851, DIN11864

SMS

SMS is the Swedish milk standard. It is designed for use in the food industry and other sanitary applications. SMS sanitary food grade pipe clamp ferrules are a series of sanitary pipe clamp ferrules used to combine three-clamp joint ends with permanent clamps in sanitary production lines. To connect the welding ends, CSE also provides long welding clamp ferrules to provide extra space for welding capacity when assembling the production line. In addition, it provides 14WMP/14MMP/14AMP three-length joints for customers to apply in the production line configuration.

Specification:

• Material grade:
• 304 and 316L / 1.4301, 1.4404
• Size Range:
• DN25, DN38, DN51, DN63.5, DN76, DN104

Product specifications

• Material grade:
  • Materials: 304 and 316L / 1.4301, 1.4404
• Size range:
  • 1", 1.5", 2", 2.5", 3", 4"

The materials is offered for food, dairy, beverage, meat processing, vacuum processing, pharmaceutical, chemical, and many other industries. It is necessary you specify at the time when orders be placing if heat numbers and MTR's are required.
Sanitary ISO Ferrules that CSE offers are made by forged. The ISO Ferrules could be conformed with ISO Blank End Cap which is made by solid bar, Clamp and other Adapters.

Product specifications

• Material:
  • Sanitary stainless steel 304, 316 and 316L
• Size range:
  • DN8, DN12, DN15, DN20, DN32, DN40, DN50, DN65, DN80, DN100, DN125, DN150, DN200
  • ISO(REP) DN8~DN250, ISO-2852
• Gasket:
  • Nitrile rubber, EPDM rubber, Teflon®, Viton® and silicone.
• Application:
  • food, beverage, dairy products, pharmaceuticals, etc.
• Material grade:
  • 304 and 316L / 1.4301, 1.4404

The materials are offered for food, dairy, beverage, meat processing, vacuum processing, pharmaceutical, chemical, and many other industries. It is necessary you specify at the time when orders be placing if heat numbers and MTR's are required. Sanitary SMS Ferrules that CSE offers are made by forged.
The SMS Ferrules could be conformed with SMS Blank End Cap which is made by solid bar, Clamp and other Adapters.

Product specifications:

• Material grade:
  • 304 and 316L / 1.4301, 1.4404
• Size Range:
  • DN25, DN38, DN51, DN63.5, DN76, DN100
  • 1/4""~12""; DN15~DN104
• Gasket:
  • Buna-N, EPDM, Teflon®, Viton® and silicone.

The materials is offered for food, dairy, beverage, meat processing, vacuum processing, pharmaceutical, chemical, and many other industries. It is necessary you specify at the time when orders be placing if heat numbers and MTR's are required. Sanitary DIN Ferrules that CSE offers are made by forged.
The DIN Ferrules could be conformed with DIN Blank End Cap which is made by solid bar, Clamp and other Adapters.

Product specifications:

• Material grade:
  • Stainless steel: 304, 316, 316L
  • Gasket: EPDM, SILICON, VITON
• Size Range:
  • German regulations: DN10, DN15, DN20, DN25, DN32, DN40, DN50, DN65, DN80, DN100, DN125, DN150
  • British system: 1",1.5",2",3",4"
• Standard:
  • DIN 11851, DIN11864
• Applications:
  • food, beverages, dairy products, pharmaceuticals, beer, etc.

3A union is composed of 3A-13H HEX. NUT, 3A-14PRF WELD LINER, 3A-15TRF WELD MALE.
CSE offers a wide variety of clamp fittings in 304 and 316L material in sizes from 1/2" to 12".
The materials are offered for food, dairy, beverage, meat processing, vacuum processing, pharmaceutical, chemical, and many other industries. Our products have earned the 3A symbol, which requires an annual assessment to make certain each product conforms in all respects to the published standard. It is necessary you specify at the time of order heat numbers and MTR's are required. Material Test Reports (MTR's) are available to document all heat number.
Sanitary 3A Ferrules that CSE offers are made by forged. Service Short Weld Ferrules- 14WMP, Middle Weld Ferrules- 14MMP Long weld ferrules- 14AMP (L14AM7), Roll- On Expanding Ferrules- 14RMP, Tank Weld Ferrules( light duty)- 14WLMP, Tank Weld Ferrules( heavy duty)- 14MPW, Tygon Hose Adapters- 14MPHT, Rubber Hose Adapters- 14MPHR
All of our 3A Ferrules could be conformed with 3A-16AMP Blank End Cap which is made by solid bar, 3A- Clamp and Seal 13PG, 13FG as well as other Adapters.

Product specifications:

• Size:
  • 3A Unions and Adapters: 1/2", 3/4", 1", 1.5", 2", 2.5", 3"and 4".
  • 3A Ferruels: from 1/2" up to 12".
• Stainless steel material:
  • 304
  • 316
  • 316L
• Gasket material:
  • EPDM
  • SILICON
  • VITON
• Roughness:
  • The roughness of the product can directly reach Ra0.8um in the turning process.

Specification:

• Materials:
  • 304
  • 316
  • 316L / 1.4301,1.4404
• Size range:
  • DN25, DN38, DN51, DN63.5, DN76, DN104
• SEAL:
  • EPDM
  • SILICON
  • VITON

Product specifications:

•  Material:
  • 304, 316, 316L / 1.4401, 1.4301
  • Sanitary DIN Ferrules that CSE offers are made by forged. DIN unions that CSE offers are made by casting, but forged material are required.
• Size range:
  • DIN UNIONS: DN10, DN15, DN20, DN28, DN34, DN40, DN52, DN70, DN80, DN100, DN125 and DN150.
  • DIN FERRULES: DN10, DN15, DN20, DN28, DN34, DN40, DN52, DN70, DN80, DN100, DN125, DN150, DN200
  • 1",1.5",2",2.5",3",4"
• SEAL:
  • EPDM, SILICON, VITON

Product Features:

• Roughness: The roughness of the product can be directly reached Ra0.8um in turning processing.

IDF union is composed of IDF-13 HEXAGONAL, IDF-14 WELD LINER, IDF-15 WELD MALE, and H TYPE SEAL.
IDF nut includes round nut, hexagonal nut and blank nut. Besides, we have WELD type and IDF expanding type which can demend what you need.
The materials are offered for food, dairy, beverage, meat processing, vacuum processing, pharmaceutical, chemical, and many other industries.
It is necessary you specify at the time when orders be placing if heat numbers and MTR's are required.

Product specifications:

• Size: 1",1.5",2",2.5",3",4"
• Material
  Stainless steel: 304, 316, 316L
  Gasket: EPDM, SILICON, VITON

RJT union is composed of RJT-13R, RJT-14 WELD LINER, RJT-15 WELD MALE, and SEAL.
RJT nut includes round nut, hexagonal nut and blank nut. Besides, we have general type and RJT expanding type which can demend what you need.
The materials are offered for food, dairy, beverage, meat processing, vacuum processing, pharmaceutical, chemical, and many other industries.
It is necessary you specify at the time when orders be placing if heat numbers and MTR's are required.

Product specifications:

• Material grade:
  • 304, 316, 316L / 1.4401, 1.4301
• Size range:
  • 1", 1.5", 2", 2.5", 3", 4", 6"
• SEAL:
  • EPDM, SILICON, VITON

Wine complete unions are composed of WINE-13 NUT, WINE-14 WELD LINER PART, WINE-15 MALE PART AND SEAL.
WINE UNION nuts includes round nut, hexagonal nut and blank cap nut. Besides, we also have general welding types and expanding types which can demend what you need.
The materials are offered for food, dairy, beverage, and many other industries.
It is necessary you specify at the time when orders be placing if heat numbers and MTR's are required.

Product specifications:

• Size Range:
  • DN40/43, DN50/53, DN60/63, DN70/73, DN80/83, DN100/103
• Material Grade:
  • 304 ,316 , 316L / 1.4401 , 1.4301
• SEAL Material:
  • EPDM, SILICON, VITON

Specification

• Imperial:
  • 1"~4"
• DIN Standard:
  • DN15~DN150
• ISO Standard:
  • ISO-21.3~ ISO-168.7
• SMS Standard:
  • DN25~DN150
• Standard
  • 3A
  • DIN
  • SMS
  • ISO
  • IDF
  • RJT
  • AS
  • BS
  • BPE
• Type Option
  • Hexagonal Tube Hanger with Blue Inserts
  • Hexagonal Tube Hanger with Inserts & Coupling Collar
    • Collar accepts 3/8″ threaded tube (not included)
    • 304 stainless steel hangers have excellent corrosion resistance.
    • Insert material is Polypropylene (PP)
  • Hexagonal Tube Hanger with Nitrile Grommets
    
    • 304 stainless steel hangers have excellent corrosion resistance.
  • Tubing Hanger W/Bolted*2 W/Blue Insert &Tube
  • A Tubing Hanger Without Tube
  • B Tubing Hanger with tube & 1/2" PT thread
  • C Tubing Hanger With Tube L=100mm
  • other can be request, please contact us.
• Application
  • Dairy products
  • Water Processing
  • Food industry
  • Beer
  • Beverages
  • Medicines
  • Cosmetics, etc.

Specifications:

• Dimension
  • 13PG EPDM 1/2" ~ 8"
  • 13FG EPDM 1" ~ 6", 10" ~12"
  • 13PG PTFE 1/2" ~ 12"
  • 13PG (EPDM+ PTFE) 1/2"~ 4"
• Material:
  • NBR
  • nitrile rubber
  • EPDM
  • Teflon®
  • Viton®
  • silicone

Product specifications:

• Material:
  • Stainless steel 316L
• Thread Connection:
  • 1/2"BSP
• Flow:
  • can be get from the picture link or send the requirement
    Clean Area Diameter: 1m to 6m
• Type:
  • Fix, rotary(optional)
• Size:
  • 1"~2.5"
  • DN10~DN50

The pressure gauge is a fluid strength measuring device. The setting and adjustment of fluid power machines require pressure gauges, and they are indispensable for Fluid line . Without  pressure gauge, the fluid power system would be unpredictable and unreliable. Gauges help ensure that there are no leaks or pressure changes that could affect the operating conditions of the hydraulic system.

Specification

• Material:
  • 304/ 316L
• Process connection：
  • 1-1/2" , 2.0" , 2-1/2"
• Quick-release clamp piping system
• Suitable Pressure Ranges：
  • 15psi to 600psi
• Instrument Connection：
  • 1/4"NPT /BSPT or 1/2"NPT /BSPT
• Max temperature：
  • standard-120°C，special-150°C

Thermometer

The thermometer has been designed as an addition to the standard range of thermometers in order to meet the special requirements of the food, bio and pharmaceutical industries as well as in the paints and varnishes industry.

Specification

• Material:
  • 304/ 316L
• Process connection：
  • Fixed male thread1/4”PT(BSPT)/ NPT；3/8”PT(BSPT)/ NPT；1/2”PT(BSPT)/ NPT
    Blind ferrule 1”；1-1/2”；2”；other
• Quick-release clamp piping system
• Temperature range:
  • -50℃ ~ +600℃
• Stram length:
  • 50mm~1000mm
• Dial Size:
  • Ø 2” ~ Ø 6”

Jacketed ball valve is used to maintain the temperature in the fluid to keep the viscosity of the fluid low to prevent jamming or crystallization.
Port connection method: Provide RJT, 3A welding end and clip connection end, IDF, DIN and SMS options can also be provided upon request.

Specification:

• Size:
  • 1/2 inch to 4 inch (DN15 to DN100)
• Application:
  • Viscous or temperature-critical food liquids, chocolate, cold syrup, fat, jam, etc.

Insulation butterfly valve:

The jacketed butterfly valve with metal jacket is welded on the outside of the valve body, and the jacket interface is installed on both sides of the valve body, which can contain steam or other superheated gas to prevent the fluid from solidifying at normal temperature or crystallization.

Specification:

• Material:
  • 304/316/316L
• Size:
  • 1" (DN25), 1 1/2" (DN40), 2" (DN50), 2 1/2" (DN65), 3" (DN80), 4" (DN100)

Insulation pipes:

The heating fittings in the food processing industry must be used in operation. The food materials transported contain substances (fats) that will solidify at ordinary room temperature or contain high-viscosity fluids to prevent jamming or crystallization. It is commonly used in media that is easy to solidify and cannot flow at room temperature, such as chocolate, grease, benzene, sulfur, sulfur, asphalt, asphalt, wax, polyurethane, resin, and fatty alcohol.
Heating accessories are divided into two categories:
-The heating part of the pipe (pipes, elbows, welding tee)
-Heating control accessories (flaps, ball valves) and special parts of piping, such as filters.
All heated accessories have a double-layer shell through which hot water can pass. Water enters the heating space through connecting fittings, usually sleeves (G 3/8", G 1/2" or G 3 /4”). The housing always has two connecting fittings (usually sleeves), one for heating Water inlet, an outlet for hot water, so that hot water can flow along the heating part of the pipe.
For hot water connection, heating fittings of size DN 25-DN 65 use connecting fittings with gap G 3/8" and G 1/2", and fittings of nominal size DN 80-DN 100 use connecting fitting gap G 3 /4" ."

Specification:

• Body material: 
  • CF3M/SS316L sulfur 0.005% ~ 0.017%
• Ball gasket material: 
  • PTFE (the design of the valve pad reduces wear and valve torque)
• Helium Leak Rate:
  • 2 Way Valve: Less than 1 X 10-7 mbar.l/sec.
• Optional:
  • pneumatic / manual

• Multiple connection option:
  • JIS 10K flange
  • KF vacuum flange
  • ISO vacuum flange
  • VCR
• Size: 
  • KF25
  • KF40
  • KF50
  • ISO63
  • ISO80
  • ISO100
• Surface : 
  • Pickled
  • Electro polish to prevent corrosion
  • Mirror polished inside and outside
• Sealed: 
  • PTFE
  • Viton
  • Others…

Feature:

Short cleaning time

Cost-effectiveness

Sanitary connection design with optimized dead angle

KF (QF) High Vacuum Flanges

KF flange (Small flange) -The ISO standard quick release flange is known by the names Quick Flange (QF) or NW. It has a counterbore or slot for joint with O-centering ring, easy and suitable for joint with Vacuum pipe line for complete system.

Size option:

KF10、KF16、KF20、KF25、KF40、KF50、KF63、KF80、KF100

ISO flange for high vacuum

ISO flange (Clamping flange) is symmetrical, so the parts can rotate. The ISO-KF vacuum flange system allows for the rapid construction of high vacuum systems without welding or brazing, and supports quick and easy cleaning or modification of the vacuum system.

ISO centering ring can not only align the flange, but also fix the O-ring In place. ISO HV flanges (limited by the characteristics of O-rings) are suitable for applications with temperatures between ~0° C and 120-180° C and pressures from atmospheric to ~10 -8 Torr or mbar.

Size Option:

DN63LF(Tube:63.5mm)、DN100LF(Tube:102mm)、DN160LF(Tube:160mm)、DN200LF(Tube:200mm)、DN250LF(Tube:254mm)、DN320LF(Tube:316mm)、DN400LF(Tube:400mm)、DN500LF(Tube:500mm)

CF (ConFlat ) flanges for ultra-high vacuum

ICF (CF) is a higher vacuum FLANGE. It is suitable for the vacuum chamber to link the main body of the ultra-high vacuum equipment and vacuum pump system or other higher vacuum connections.

ICF flange (Con Flat Flange) is separate to fixed type, rotating type, screw bolt hole type and threaded type. Let Flange be completely fixed, and there is a raised sharp edge inside. It is made of an all-metal seal by squeezing a copper gasket to deform it to achieve the purpose of sealing the vacuum. Widely used in ultra-high vacuum field equipment.

The working pressure range of the seal is 760 Torr (1013 mbar) to <1 x 10 -13 Torr (<1.3 x 10 -13mbar), and in the temperature range of -196° C to 450° C (depending on the material。

• Seal pressure range:
  • 760 Torr (1013 mbar) ~ < 1 x 10 -13 Torr (<1.3 x 10 -13mbar)
• Seal Temperature range:
  •  -196° C ~ 450° C (depends on material)
• Size:
  • CSE provides OD inch, ISO, and A312 A full-size flange services.
• Material:
  • SS304
  • 304L
  • 316L
  • other special requirements.
• Surface Finished:
  • Mechanical processing, electrolytic polishing.

These KF type aluminum/stainless steel SS304/316L clamps use ISO-KF Flange. They are usually used in vacuum piping systems to connect standard NW/KF vacuum components. Can be assembled quickly and easily for Joint Flange and centering ring for complete vacuum system ( centering ring rubber O-ring Can make the width material choice) .

• Material: Aluminum ADC 12
  • Size:
    • DN 10 / 16 ISO-KF
    • DN 20 / 25 ISO-KF
    • DN 32 / 40  ISO-KF
    • DN 50 ISO-KF

• Material: Stainless Steel 304
  • Size:
    • DN 10 / 16 ISO-KF
    • DN 20 / 25 ISO-KF
    • DN 32 / 40  ISO-KF
    • DN 50 ISO-KF

Each component contains two flanges and a centering ring, which are connected together by a clamp. The centering ring keeps the flanges in a straight line and prevents the O-ring from being pushed in by atmospheric pressure. In different specifications A different number must be used to ensure a firm connection.

C-type clamp, used for connecting products between ISO/ICF flanges. The material can be used aluminum alloy or stainless steel for joint with ISO Flange or ICF Flange safety clamping purposes.

• Application:
  • Used in the piping system of the semiconductor industry to fix 2½"-10" vacuum tube fittings
• size:
  • ISO63/100
  • ISO160 / 250
  • ISO320 / 500
  • ISO630
• Material:
  • Accessories: 304 or 316L stainless steel
  • Clip: Aluminum
  • O-ring: FKM

NW/ KF centering ring 304 stainless steel with O-ring, used for front vacuum pipelines and high vacuum chamber ports connection, used in the vacuum industry; in addition, O-rings with mesh can be provided to prevent small particles from entering the pump and other vacuum industries. The KF clamp and the centering ring form a vacuum seal between the connecting flanges. The center ring is made of 304 stainless steel/ aluminum, so it will not be out of shape and can ensure tight up the pipeline connection.

• Material:
  • VITON O-RING + aluminum alloy Centering Ring
  • VITON O-RING + stainless steel Centering Ring

Hydraulic bellows (Compressible Bellows) are used in highly flexible pipeline systems, usually connected to remote vacuum pumps, vacuum manifolds, to reduce vibration transmission, and able to withstand low leak rates to ensure a hermetic seal.

Edge-welded bellows (Flexible Hose) can provide vacuum CF (conflat), ISO vacuum flange required operating distance, bore size, vacuum container to match the connected flange and manifold.

The vacuum Bellow is Forming out complete 0.2mm thick stainless steel pipe. It has high elasticity and bending characteristics. It is applied to the connection between the flange and flange, and has a good shock-proof and bending effect.

Specification:

• Material:
  • stainless steel 304
  • can be required stainless steel 316L
• Length:
  • 100mm~1000mm
• Wall thickness:
  • 0.14~0.4mm
    • 0.15mm has good flexibility
    • 0.2mm good strength
• Temperature range:
  • -200°C~ 450°C
• End connection:
  • KF/ NW flange
  • CF/ CR flange
  • ISO/ LF flange
• Polishing:
  • Inside/ Outside surface polishing, mirror polishing
• Application: High vacuum/ ultra-high vacuum, connection pump, convenient for connection and bending
• Features: Flexible, easy to bend, vibration absorption, leak test, good flexibility, flexible short bellows

The pneumatic ball valve adopts a high platform design, which is easy to disassemble and assemble without the use of an adapter frame. It is equipped with an aluminum alloy cylinder that is lightweight and durable. The ball valve platform adopts ISO-5211 standards and uses ultra-durable all-inclusive Teflon to comply with sanitary design. The series has passed the US 3A food unit certification, allowing you to use it with confidence.

The sanitary ball valve is made of stainless steel CF3/SS316L. Additionally, it offers ASME BPE compliant surface treatment (electropolishing: helps improve corrosion resistance/mechanical polishing) to ensure product line cleanliness.

Port connection standards: SMS, DIN, 3A, ISO, and RJT are available.

• Sizes: 1/2" to 6".
• Flow channel: Ball valve types include two-way, three-way, four-way, etc.
• Ball pads: can be divided into half-pack and full-pack types. The ball pads are designed using FDA-certified materials from major international manufacturers, including PTFE, PTFE+ Carbon, PTFE+GB, and PTFE+50%SS.
• Automatic control matching: It can also be matched with a pneumatic head (single-action Air/Spring or double-action Air/Air) and a positioner to facilitate various automatic controls.

 CSE ball valves are available for manual & pneumatic types, they can be used in the pharmaceutical, biotechnology, semiconductor, dairy and food industries.

The main function of Ball vales is to open/close to change the flow direction of the medium.

With its simple structure, compact size and easy operation.

The sanitary ball valve is made of stainless steel CF3/SS316L. Also, CSE offers ASME BPE-compliant surface treatment (electropolishing(Raise corrosion resistance) /mechanical polishing) to ensure product line cleanliness.

Manual sanitary ball valves are available for low-platform design and high-platform design. The ball valve platform follows ISO-5211 standards, which are easy to disassemble and clean.

The entire series has passed the USA 3-A certification and uses a durable full cavity PTFE seal to comply with hygiene design allowing you to use it with confidence.

○The low platform design makes the valve lighter & more compact; the use of CSE stainless steel is more textured and hygienic.

○The high platform design can be directly installed with CSE aluminum actuator, without adapter request and is lightweight and durable.

• Connection standards of port: SMS, DIN, 3A, ISO, RJT are available.
• Sizes: 1/2" to 6".
• Flow Type: two-way, three-way, four-way, etc.
• Ball seal: can be half-cavity and full-cavity seat types. The ball seal passes FDA-certified and the material is from major international manufacturers, available PTFE, PTFE+ Carbon, PTFE+GB, and PTFE+50%SS.
• Automatic control: It can be installed with a pneumatic actuator (single-action Air/Spring or double-action Air/Air) and has an option for the positioner or IOT control boxes.

o The best check valve type of the piping or tubing system for drainage installation.

With six-leg central stem designed to be installed in a horizontal tubing system without the risk of incomplete on/off due to incorrect stem angles.

The valve of horizontal tube can facilitate emptying and make system zero residual , maintaining hygiene and purity in the pipeline system.

• Vertical check valve/ Non-return valve

o Vertical design to prevent reverse flow under strict high purity system.

The valve closes/opens, when the spring pressure exceeds the pressure under the flow plate, .

The material of valve 316L stainless steel valve body and seat, which can be quickly disassembled or installing through sanitary clamp design.

Product specifications

• Material:

o Body/Steam : ASMT SS316L

o Seal: EPDM, Silicone, Viton(FKM),PTFE

• Connection method:

o Welded end

o Clamp end

• Standard:

o 3A

o SMS

oBS

o DIN

• Open pressure: